High Quality Corrugated Cardboard Paperboard Carton Box Flexo Automatic Feeding Printer Slotter
Product Type: Box
Paper Type: Corrugated Board
Printing Type: Flexographic Printing
Surface Finish: Varnishing
Coating: Coated
4 Colors Carton Printing Slotting Die Cutting Machine with StackerDetailed configuration and technical parametersMachine performance• Computer control can store common orders, change orders faster and operate more conveniently.• All drive rolls are made of high quality steel, hard chrome plated, and grinding.• Oil automatic balancing device keeps the oil in each unit at the same level.1.paper feeding unit (one group)(1) Sun wheel box leading edge paper feeding system.A. Four-axis leading edge paper feeding, increase fan flow, and maintain accurate speed when feeding at high speed and low speed.B. Adjust the airflow and pressure in 4 steps to match the cardboard size.C. Positioning from the front to reduce paper feed errors and improve the accuracy of paper feeding, printing and slotting.D. Electric control of left and right side baffles, computer adjustment.E. Rear pallet holder electric control front and back.F. Manual adjustment of the front stop cardboard gap.G. Paper can be fed continuously or separately. (Continuous or separate sheets can be selected as needed).H. Paper feed counter, set, display the production quantity.(2) paper feeding upper and lower rollersA. upper roll; outer diameter of 155mm, steel pipe surface wrapped wear-resistant rubber, balance correctionB. Lower roll: The outer diameter is 155mm. The surface of the paper feed roller is embossed and hardened.C. Feeding pressure roller adjustment gap is adjusted by self-locking structure, the adjustment range is 0-12mm.D. The power transmission of the pressure roller adopts the rolling cross coupling transmission to reduce the wear and make the transmission more balanced.(3) machine clutch, automatic return zero deviceA. The drive shaft is equipped with a friction clutch to avoid malfunction and damage the machine.B. Main engine start protection device (when the machine is not locked, the main unit cannot start running).C. Paper feeding unit, printing unit and slotting unit are electrically and automatically reset to zero.D. The general carton uses the automatic zeroing device. It can be adjusted to the correct position by printing 1 or 2 sheets of paperboard to reduce the waste of cardboard.5. Dust removal device, the printing plate can not stick to impurities during printing to reduce the number of plate wiping.6. The special leading edge device does not destroy the strength of the cardboard.2. Printing unit(1) printing rollerA. The outer diameter is 395.6mm.B. is made of high quality steel with surface grinding and hard chrome plating.C. Balance correction, smooth operation.D. Reel hanging version, using the left and right locking devices to make the hanging version more accurate.E. full version of the hanging groove, suitable for 10mm hanging strips.F. Loading and unloading the printing plate, the electric control of the foot switch Positive reverse.(2) Printing pressure rollerA. outer diameter is 176mmB. The surface of the steel pipe is ground and hard chrome plated.C. Dynamic balance correction, smooth operation.D. Pressure roller gap adjustment adopts self-locking structure adjustment, the adjustment range is 0-12mm.(3) Metal anilox roller (three group)220 mesh two units, 250 mesh one unit.A. The outer diameter is 200mm.B. The surface of the steel pipe adopts advanced electroplating chrome process, which is hard, smooth and wear-resistant.C. The dots are consistent and the ink is even.D. Extend the life of plates and rubber rollers.E.The adjustment of the anilox roller gap is adjusted by the self-locking structure , and the adjustment range is 0-12mm.(4) Rubber roller (three group) A. The outer diameter is 195mm.B. The surface of the steel pipe is wrapped with wear-resistant rubber.C. The rubber roller has high special grinding and good ink transfer effect.D. Rubber roller gap adjustment adopts self-locking structure adjustment, the adjustment range is 0-12mm.(5) phase adjustment mechanismA. Planetary gear structure.B. Printing phase adopts electric digital control 360 degree adjustment (can be adjusted both in running and stop.) The adjustment value is more accurate.C.The lateral phase of the printing roller is electric adjusted, and the adjustment range is ±10mm.D. Printing plate roller adopts electric adjustment phase, fast adjustment speed and high precision of adjustment.(6)Feeding paper rollA. The upper paper feeding roller, with an outer diameter of 125mm, is made of high-quality steel hard chrome-plated and equipped with 3 wrenches, and the shaft can be rotated to any position with adjustable paper guide wheels.B. Paper feed lower roller, outer diameter is 155mm, the paper guide roller is plated with hard chrome.C. The adjustment of the paper guide roller gap is adjusted by the self-locking structure , and the adjustment range is 0-10mm.(7) ink circulation structureA. Pneumatic diaphragm pump, stable ink supply, easy operation and maintenance.B. Ink filter to filter impurities.C. Low ink alarm.D. When printing, the rubber roller can follow the preset speed and rotate at a constant speed to improve printing clarity.(8) printing phase fixing deviceA. The pneumatic brake mechanism is adopted. When the unit is separated and adjusted for phase or cleaning, the brake mechanism limits the gear rotation and maintains the fixed position of the original gear position.B. The power transmission of the pressure roller adopts the rolling cross coupling transmission to reduce the wear and make the transmission more stable.3. Slotting unit (one group)(1) Single-axis double-knife slotting, the height of the box is adjusted by internal teeth, so that the lubricating oil is not easy to contaminate the carton.A. The diameter of the press-line shaft is 110mm high-quality steel, grinding and processing, and the surface is plated with hard chrome.B. The cardboard after pre-pressing is not easy to be crushed.C. The adjustment of the pressure roller is adjusted by the self-locking structure , and the adjustment range is 0-12mm.(2) The horizontal movement adjustment mechanism of the slotting tool holder adopts a screw rod and a linear guide sleeve to make the movement more flexible and accurate. The pre-pressing wheel and the actual pressing wheel adopt quick-change devices.A.Slotted cutter shaft is made of 156mm high-quality steel, ground and hard chrome plated.B. Slotting knife width 7mm.C.Slotting adopt three knives moving adjustment.C. Slotting knife clearance adjustment adopts self-locking structure adjustment, the adjustment range is 0-10mm. .(3) Slotted phase adjustment mechanism.A. Planetary gear structure.B. The slotted phase is adjusted by computer control (operation, stop, and adjustment).Computer and button dual system adjustment.4. Die cutting unit (one group)(1) Rubber pad roller mechanical reversing 40mm swimming transverse structure.A. The outer diameter of the pad roller is φ404mm.B. Rubber pad roller is made of high quality steel with surface grinding and hard chrome plating.C. Balance correction to increase operational stability.D. The thickness of the pad is 8mm and the width is 250mm.E. The clearance between the pad roller and the die roll is adjusted by the self-locking structure, and the adjustment range is 0-16mm.F. Rubber pad roller automatic compensation structure, automatic control pad roller speed.G. Rubber pad roller cutting and flattening structure, keeping the rubber pad roller flat.(2) die roll φ487mmA. The die roll is made of high quality steel with a surface finish and hard chrome plating.B. Dynamic balance correction, increase operational stability.C. The distance between the screw holes of the die set is 100mm in the horizontal direction and 20 equal in the radial direction.D. Applicable pressure line height is 22.60mm.E. Wood template thickness 13mm, blade height 25.4mm(3) Die-cut phase adjustment mechanismA. Planetary gear constructionB. Die-cut phase adopts electric digital control 360 degree adjustment (operation, stop can be adjusted)(4) Guide roller gap adjustment adopts self-locking structure adjustment, adjustment range 0-12mmA. The power transmission of the paper guide roller adopts the rolling cross coupling transmission to reduce the wear and make the transmission more stable.4. Stacker unit A. The paper receiving can be operated automatically or manually.B. The left and right alignment device for receiving paper makes the cardboard stack more neatly, and the stack height is 1700mm.C. The bed is driven by powerful chains.D. The paper receiving platform is equipped with an anti-fall device when ascending to ensure the safety of the operator.E. The paper receiving pallet is operated by air pressure. When the cardboard is stacked to a predetermined height, the receiving pallet automatically extends to support the cardboard.F. Flat wrinkled belt to prevent the cardboard from sliding down.G. The belt of the receiving arm can be adjusted individually for tightness without being restricted by the length of the belt.5. the main technical parametersModel number: 1224Maximum mechanical speed: 220 sheets / minuteMaximum paper feed size: 1200mmX2600mmMinimum paper feed size: 350mmX500mmSheet skip feed size: 1400mmx2600mmMaximum printing area: 1200mmx2400mmMinimum slot gap250mmx70mmx250mmx70mmMaximum groove depth320mmWall panel thickness: 50mmPaper feeding accuracy: ±1.0mmPrinting accuracy: ±0.5mmSlotting accuracy: ±1mmMain motor power: 18.5KWTotal power: 29KWDelivery Pictures:Carton box pictures:Customer Visit:
Diamond Member
Audited Supplier
4 Head I3200 Digital Dtf Printer Machine 60cm Pet Film Offset T-Shirt Printing with Machine Shake Powder
After-sales Service: Online & on Door Service
Warranty: 1.5year
Plate: Lithography Printing
Structure: Platen Press
Color & Page: Multi-Colour Printing Press
ModelXYS-01 DTFPrinter Printhead Epi3200Print Width60cmInk Colors C M Y K + WInk TypePigment InkConsumptionCMYK is 15-20ml/sqm, CMYK+W is 25ml/sqmRIP SoftwarePhotoprintPrint File FormatBMP, TIF, JPG, PDF Etc.Heating SystemExtra Front Heating SystemFeeding MethodRoll to Roll, LeafColor ManagementICC Based; Density & Curves AdjustablePower Supply50HZ/60HZ, 220V, 10A
Fully Auto Cardboard Box Flexo Printing Machine Price
Certification: UL, TUV, CE
Driven Type: Electric
After-Sales Service Provided: Overseas Third-Party Support Available
Type: Automatic Carton Making Machine
Automatic Grade: Automatic
full auto cardboard box flexo printing machine priceprinting slotting die cutting machine can complete 1-3 color printing, cutting, pressing, trimming, grooving, Angle cutting, die cutting, punching and other processes of the cardboard at one time. Leading edge adsorption paper feeding, adjustable air volumeComplete Machine Specification ItemMODEL1020122414281630Max speed220s/min180s/min160s/min140s/minMax feeding size1000*2000mm1270*2600mm1500*3000mm1660*3200mmSkip feeding1250*2200mm1500*2600mm1800*3000mm2000*3200mmMax print area950*2000mm1200*2400mm1430*2800mm1600*3000mmStandard thickness7.2mmMin slot gap(nomal)150*150*150*150mm150*150*150*150mm160*160*160*160mm Min slot gap(reverse)230*65*230*65mm230*65*230*65mm250*70*250*70mm Board thickness2.5 - 9mm2.5 - 12mmMax slotting depth250mm320mm390mm430mmComputer system control, can store commonly used orders, change orders more quickly.Fault alarm function, production control, remote maintenance.The flexo printing slotting die cutting machine for sale adopt vacuum adsorption way to transport board, transmission precision is high, effectively ensure the printing effectAutomatic detection and positioning system, fast board drive system, quick order replacement. Detailed ImagesAuto feeder 1.Lead Edge feeder system, inverter adjust air volume, feeding in precision and steady2. Double feeding roller model. Quick replacement mechanism for the first feeding rubber roller, with spring adjustment function, it can prevent distortion and ensure accurate feeding of cardboard.3.Brushes and suction device remove dust from board surface.4.Touch screen displays production speed and quantity5.Adjust the feed interval by manual Printing parts Both printing cylinder and impression cylinder are made of high quality steel with grounding surface and chrome plated. Dynamic and static balance correction ensure to run stabilityAdopt hanging structure, convenience and fast to set up.Installing and uninstalling printing plate with pedal switch or operation panel to control forward and reverse.To match with feeding unit the machine with automatic lift anilox, when the feeding unit runs, the anilox roller goes down to contact with printing plate, while on contract, leave printing plate.Phase position utilizing electromagnetic clutch locking device, with intelligent zeroing function and can reset in dynamic and static conditionPrinting phase adopt PLC touch screen and 360 degree electric adjustmentPull roller quick lateral moving mechanism, self-locking gap adjustment deviceSlotting parts Unique double slotted structure, elimination of collision between from and back tool, processing of large size high carton boxThe slot knife thickness is 7- 8 millimeter, which is from high quality alloy, tooth profile in sharp cutting, high wearableThe slot knife with phasing and box height adjustment device, the frequency changer control the dynamic 360 degree adjustmentPrecision linear slide way, accurate lateral movement with smooth slottingRegards the user's need it can match the punch devicePre-creaser, crease, slotting knife holder, self-locking gap adjustment deviceSpring type single slitting knife with glabrous slitting effect and cost savingMiddle knife motorized moving device, fit for each productionDie cutting partsDie cut unit roller adopt high quality steel, plated with rigid chrome.Mould roller and rubber roller can auto separate by cylinder eccentric device when the machine don't die cut, this can lighten machine load and increase rubber roller and die knife lifeMatching with feeding system, it with auto up and down device, the rubber roller will down when feeding paper. The rubber roller will up when stop feeding paper. To make sure every paper die cut correctlyThe mechanical transmission rubber roller move 58 mm in left and right side. It also with wear and tear tegular could increase the life of rubber roller.Die cut phase adopt PLC touch screen, 360 degree adjust electric numberMachine with rubber amend device, the rubber roller can be used after many times amendFree die mould slotting unit, no need to make the die mould when making normal box, saving cost and improved efficiently(optional)Details Finished Carton box Applicable industryClothing factory, shoe factory, food factory, pharmaceutical factory, pesticide packaging, beverage packaging box, handicraft packaging, cup packaging, electrical packaging, battery car packaging, children's toys packaging, logistics packaging, furniture packaging, all kinds of small commodity packaging, industrial small parts packaging.Company Information Packaging & Shipping 1)Inside packaging could be iron frame:it is more firm to avoid shake and damage.2)Outside packaging could be wooden case: the wooden case is of soft texture could reduce damage from impact 3)Waterproof plastic: keep goods dry and avoid damp4)We also accept customized regarding the packageTrade Shows Customer visit For now, we have client from South east Asia and south Asia, Middle east, Europe, American, Africa and so on place. They buy not only flexo printing slotting die cutting machine for sale but also other product we supplied. In addition, we could help customer to order other product we dont production.Customers are welcome to visit our factory and most of them satisfied with our product quality, factory scale as well as our service. If you are interesting, please dont hesitate to come meet us! Certificate Our Services1)Three years warranty for machine. technical to door service.2)English manual and Video for machine using and maintenance.3)We offer free training in our factory, welcome to visit and learn more about our machines.4)Free accessories: Software ,manual, book, videos, USB control FAQ1. Are you a trading company or factory?We are the manufacturer and also we have import export license. 2. Where is your company located? How can I visit there?Our factory address: dongguang county, Cangzhou city, hebei province,China3. Can you send technician for installation and training?Yes, we can send our technician abroad for installation and training, but all the charges must be paid by buyer, such as the plane tickets (a round trip), meals, hotel, traffic etc. 4. Whats your warranty timeWe can take 3 years warranty, actually our longest cooperation customer have been using our product for more than 10 years with no problem.Contact info